Node riak at 192.168.56.101 is not reachable in riak-yokozuna-0.10

m-hou at fores.jp m-hou at fores.jp
Thu Oct 24 23:56:38 EDT 2013


Thank you for your quick responses.

Here are the output of "ifconfig -a" from these three VMs:

--------------------------No.1----------------------------------------
eth0      Link encap:Ethernet  HWaddr 08:00:27:8F:13:9F
          inet addr:192.168.56.101  Bcast:192.168.56.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fe8f:139f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:834 errors:0 dropped:0 overruns:0 frame:0
          TX packets:865 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:485050 (473.6 KiB)  TX bytes:646613 (631.4 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2738 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2738 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:216477 (211.4 KiB)  TX bytes:216477 (211.4 KiB)
--------------------------No.2----------------------------------------
eth0      Link encap:Ethernet  HWaddr 08:00:27:E3:3E:4F
          inet addr:192.168.56.102  Bcast:192.168.56.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:fee3:3e4f/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:692 errors:0 dropped:0 overruns:0 frame:0
          TX packets:632 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:416875 (407.1 KiB)  TX bytes:328019 (320.3 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:2998 errors:0 dropped:0 overruns:0 frame:0
          TX packets:2998 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:230984 (225.5 KiB)  TX bytes:230984 (225.5 KiB)
--------------------------No.3----------------------------------------
eth0      Link encap:Ethernet  HWaddr 08:00:27:BC:90:55
          inet addr:192.168.56.103  Bcast:192.168.56.255  Mask:255.255.255.0
          inet6 addr: fe80::a00:27ff:febc:9055/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:789 errors:0 dropped:0 overruns:0 frame:0
          TX packets:752 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:477451 (466.2 KiB)  TX bytes:391998 (382.8 KiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:801 errors:0 dropped:0 overruns:0 frame:0
          TX packets:801 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:67978 (66.3 KiB)  TX bytes:67978 (66.3 KiB)
------------------------------------------------------------------

additionally, in the same three VMs I installed riak-yokozuna-0.8.
I succeeded to setup a 3 nodes cluster.

Thanks again!
Houm


> Hello Houm,
>
> Could you provide the output of "ifconfig -a" from these three VMs? Are
> you
> using NAT or host-only networking?
>
> --
> Luke Bakken
> CSE
> lbakken at basho.com
>
>
> On Wed, Oct 23, 2013 at 6:24 PM, <m-hou at fores.jp> wrote:
>
>> Hello All,
>>
>> I have setup three VMs using VirtualBox running centos and installed
>> riak-yokozuna-0.10. I have changed the 127.0.0.1 to the actual IP
>> in the riak.conf on each of the VMs. I can start the nodes and ping,
>> but I keep getting the not reachable error when I type 'riak-admin
>> cluster join riak at 192.168.56.101'. I noticed that the settings are
>>  located in app.config prior to riak-yokozuna-0.8.
>>
>> ----------------------------------------------
>> { kernel, [
>>             {inet_dist_listen_min, 6000},
>>             {inet_dist_listen_max, 7999}
>>           ]},
>>
>> ----------------------------------------------
>>
>> How do I config the settings in riak-yokozuna-0.10?
>> Anyone have any ideas?
>>
>> Thank you!
>> Houm
>>
>> _______________________________________________
>> riak-users mailing list
>> riak-users at lists.basho.com
>> http://lists.basho.com/mailman/listinfo/riak-users_lists.basho.com
>>
>





More information about the riak-users mailing list